Announcement

Collapse
No announcement yet.

Help needed T_T MR ian

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Ian
    replied
    440 kpa absolute, so 3.4 bar of boost. If you are going near that limit make sure you set high values in the MAP sensor Limp Home Table in case the limit is exceeded.

    Leave a comment:


  • Khooyi
    replied
    anyone know how many bar map sensor is build in for SM4 PNP evo9 version 1.07

    Leave a comment:


  • Chris
    replied
    Might be winding up the iac adapt % . Need a log of normal idle and
    when stopping.

    Leave a comment:


  • sarde
    replied
    I am in agreement with Ian as the stepper may very well be the cause of the rapid and drastic increase in engine speed. What you can do is complete a log reflecting the commands being sent to the stepper motor and its position while the problem is happening. This is of course assuming that the problem can be repeated quite easily. Are you comfortable setting up logging parameters within the software?

    Leave a comment:


  • Khooyi
    replied
    i change a new set of throttle body with stepper motor.It was working perfectly fine before the tune. The spike will come when i stop the vehicle. that means is after driving and closing the throttle when coming to a stop.

    Leave a comment:


  • Ian
    replied
    It is maybe the stepper motor control more than the throttle. Is the spike after starting the engine or after driving and then closing the throttle?

    Leave a comment:


  • Khooyi
    replied
    Thank you for the reply. Ian. It has been a great help. i have some issue with the idling now after the tune. i have just change the throttle body and the problem still coming back. idle not stable will spike to 3000rpm for 5 sec then drop to normal idle. is there any possibility of ECU faulty?

    Leave a comment:


  • Ian
    replied
    Yes, if the Evo 8 is a JDM with the same 3 plug connector. You need to turn the variable cam parameters Off and also change to the Autronic MAP sensor (or fit an external MAP sensor) as Evo 8's did not have the MAP sensor in the manifold.

    Leave a comment:


  • Khooyi
    replied
    Thank you for helping. MR IAN
    may i ask if the evo9 PNP SM4 can install into a evo8 and get it tune?

    Leave a comment:


  • Ian
    replied
    A cal is attached for an E9 JDM with v1.07 configured for Mitsubishi MAP and Air temp sensors, Autronic Baro sensor and dual boost solenoids.

    For that cal check the following jumper links on the circuit board;
    JP2 (air temp) - link on pins 2 & 3,
    JP51 (MAP sensor) - link on pins 2 & 3,
    JP55 (Baro sensor) - link on pins 2 & 3.
    Attached Files

    Leave a comment:


  • Khooyi
    replied
    its a JDM model!

    Leave a comment:


  • Khooyi
    replied
    I'm not sure. the vehicle is brought and use in Singapore?

    please help

    Leave a comment:


  • Ian
    replied
    JDM or export model?

    Leave a comment:


  • Khooyi
    started a topic Help needed T_T MR ian

    Help needed T_T MR ian

    Hi anyone has autronic sm4 version 1.07 Pnp evo9 base map?
    please help.


    my email
    Khoo_yi88@hotmail.com
Working...
X
gerçek jigolo şirketleritokat jigoloprofesyonel jigolo sitesigüvenilir jigolo siteleritürkiyenin yasal jigolo sitesiizmir jigolo sitesiankara nakliyatankara nakliyatistanbul nakliyatankara nakliyatjigolo plusviagraankara evden eve nakliyatankara nakliyatpendik saç ekimibahis sitelerilewdup.com
#yaslikurt#>maltepe escort
ümraniye escort ataşehir escort escort bayan
Hack haber Hacklink Hack forum Hd film izle php Shell indir Hack haber