Need help with mu PNP for subaru

[MARKSTIV8]

I have Autronic PNP My 2001-05 Subaru
Serial number 0043
I need to find out more information on it
What model is it what futures it has?
And haw much is knock board. For it?
Can it be installed by me or is it to hard to instal knock board?
Thank You for your Help

[Ian]

That is an early ECU but it has the same functionality available as new ECU's. The main thing to check is the firmware version. It would have been produced with 1.02 or 1.03 firmware but may have been subsequently upgraded. You can tell from the sticker on the CPU (the chip in the socket) and if it is less than v1.06 it would recommend to upgrade it to v1.06 or later.

The knock adaptor is not difficult to install if you are careful. I will send you an email.

[MARKSTIV8]

Haw much is the upgraded CPU? Can I change it my self? Where can I buy it?
Haw much is knock sensor and where can I buy it?

Thank You

Mark

QUOTE=Ian;15028]That is an early ECU but it has the same functionality available as new ECU's. The main thing to check is the firmware version. It would have been produced with 1.02 or 1.03 firmware but may have been subsequently upgraded. You can tell from the sticker on the CPU (the chip in the socket) and if it is less than v1.06 it would recommend to upgrade it to v1.06 or later.

The knock adaptor is not difficult to install if you are careful. I will send you an email.[/QUOTE]

[MARKSTIV8]

Please contact me I have a 1.05 Chip in my board and like to buy the newest version.

Thanks

Mark


That is an early ECU but it has the same functionality available as new ECU's. The main thing to check is the firmware version. It would have been produced with 1.02 or 1.03 firmware but may have been subsequently upgraded. You can tell from the sticker on the CPU (the chip in the socket) and if it is less than v1.06 it would recommend to upgrade it to v1.06 or later.

The knock adaptor is not difficult to install if you are careful. I will send you an email.

[MARKSTIV8]

Hi Ian.

I try to send you a PM but cant do it.

I need your help with my PNP board to determine IF it is GOOD or NOR.

Please PM me your email so I can send pictures and explain my concern.

Thank You
Mark

That is an early ECU but it has the same functionality available as new ECU's. The main thing to check is the firmware version. It would have been produced with 1.02 or 1.03 firmware but may have been subsequently upgraded. You can tell from the sticker on the CPU (the chip in the socket) and if it is less than v1.06 it would recommend to upgrade it to v1.06 or later.

The knock adaptor is not difficult to install if you are careful. I will send you an email.

[MARKSTIV8]

Here is the link to the pictures as you can see in the pictures there is a resistor R57 (you can see it clear in the next picture below the pencil) missing Im pointing with pencil at it (i can tell it was there as the soldering is telling me it it not factory finish)
http://i1142.photobucket.com/albums/n610/markatmjm/CIMG3208.jpg

[MARKSTIV8]

Here is the one with 2 cuts to the board im pointing at it is right behind the resistor missing on the board
http://i1142.photobucket.com/albums/n610/markatmjm/CIMG3207.jpg

[MARKSTIV8]

This one is showing a small cut by the sensor with the house coming out of it.
http://i1142.photobucket.com/albums/n610/markatmjm/CIMG3211.jpg

Thank You for Your help.

[MARKSTIV8]

BUMP....

Can anybody look at the pictures and tell me if this is OK???

[Ian]

info@ecuglobal.com.au

[MARKSTIV8]

Email sent.

Thank YOU


info@ecuglobal.com.au